M1 Carbine Parts Grouping for sale in Dallas Texas

$1,500.00

PLEASE READ EVERYTHING BEFORE CONTACTING ME

For sale is an M1 Carbine parts grouping. $3500 worth of parts being sold for a fraction of the cost, $1500, as I have liquidated my M1 Carbine collection. The parts are in great condition. Soma have dried up grease but can be cleaned off with acetone. I have included a list below. The parts were stored indoors of a smoke-free home. SEE PHOTOS

$1500. CASH ONLY. Priced to move. My loss is your gain.

PARTS LIST

Walnut stock, no hardware

Birch stock, some hardware

Lower/ trigger housing group

• Trigger housing group (complete), National Postal Meter (N16) Type II - $350
o Underwood hammer
o SW – Irwin Pedersen sear

• Trigger housing, National Postal Meter (N6) Type Unknown - $175
o Hallmarks of an M2 conversion are present, but never finished out
o Features of both Type II and Type VI
o NPM stamp on wrong side
o Narrow rear wall of the magazine well
o M2 selector spring notch not present
o Mark for small hole present, but not drilled
o M2 milling allowance for sear is marked, but not present

Slides

• Slide, M1, “E” marked Type II - $100
o “PI” marked inside bottom
o Carbines Collectors Club Category L169A

• Slide, M2 (M1 Type V to M2 ordinance modified 7160091), Winchester, modified Type V - $200
o “PI” marked inside bottom
o Carbines Collectors Club Category L379B

• Slide, M2 (D7161843), “K” marked Type VI - $200
o “PI” marked inside bottom
o Carbines Collectors Club Category L479B

Hammers & Hammer Springs

• Hammer spring, Type I, 22 coil - $12
• Hammer, IBM (AMB) Type III - $45
• Hammer, Inland (HI) Type III - $45
• Hammer, Inland (HI) Type IV - $75
o Machined for M2 select fire

Trigger pin / Recoil springs / Spring guides

• Trigger pin - $3
• Recoil spring x6 - $60
• Recoil spring guide x3 - $45

Bolts & Bolt tools

• Bolt assembly / disassembly tool - $95
• Bolt (stripped), Flat top, Inland (IO 1) - $215
• Bolt (stripped), Flat top, Inland (IO 2) - $215
• Bolt (complete), Flat top, Inland (IO 2) - $345
• Bolt (complete), Flat top, Saginaw (SG) - $280
• Bolt (complete), Round top, Underwood (U) - $280

Firing pins & Springs

• Firing pin, Underwood (U) - $60
• Spring, Firing pin, - $8

Recoil plates

• Recoil plate, (DI) Type III - $40

Butt plates

• Butt plate, late, unknown (Winchester?) - $25

Oilers

• Oilers, Unopened pack of 6, Saginaw - $270
• Oiler, Quality (IQ) - $45
• Oiler, Standard Products (ISP) - $45
• Oiler, International Silver (IS) - $35
• Oiler, National Postal Meter (IN) - $45
• Oiler, Unknown (BK) - $20

Other carbine tools

• Piston nut wrench - $35
• .30 Bore brush, brass -$ $2

Garand / M14 / M1A Parts

Tools / Cleaning

• M10 Combination tool x3 - $45
• Patch loop tip x11 - $55
• M14 Gas plug wrench, Bridgeport Hardware (BHA CORP) x3 - $50

PLEASE READ! FIRST COME FIRST SERVE! The first one to meet me with money in hand gets the item. I will NOT hold nor ship the item. I have lost out on too many deals holding items for people in the past, thus getting screwed over.

AGAIN, NOT SHIPPING, LOCAL PICK UP ONLY.

If you have any questions, please do not hesitate to message me.

If you wish to purchase, I will meet you at 7-11 on Main and Hillcrest here in Frisco across from Brinkmann Ranch. BRING EXACT AMOUNT!

All sales “as is” and final. I make no guarantees nor warranties.

Thanks!